Predator 60 / 60 SE

Predator 60 $849.0 / Predator SE 60 $1099.00

• Machined aluminum center hub
• Full bearing supported & adjustable seesaw for FAI or 3D
• Floating feathering spindle with adjustable damping
• High tilt flybar with rigid flybar control yoke
• Machined aluminum, full bearing supported bell-hiller mixers
• Adjustable bell-hiller ratio allows tuning for preferred cyclic response
• Heavy duty main rotor grips with 5mm long shank blade bolts
• Blade grips will accommodate any blades with 12mm to 18mm blade roots
• 690mm symmetrical Aerotech Plus ARF main rotor blades (standard kit)
• Large one-piece 29gr flybar paddles for sport and 3D flying
• Two radial bearings and a heavy duty thrust bearing in each blade grip
• 10mm Hardened main shaft
• Aluminum head button included (SE model only)
• 20g 3D and 29g sport flybar paddles included (SE model only)
• RotorTech 700mm carbon fiber main blades (SE model only)

• eCCPM 3 servos system with bellcranks to absorb rotor head vibration
• Electronic CCPM (cyclic collective pitch mixing) at 120 or 140 orientation
• Push-pull dual bearing supported roll cyclic bellcranks
• Direct dual bearing supported fore-aft cyclic bellcrank
• Dual bearing supported washout control arms
• Washout base with brass sleeve for zero slop
• Precision machined dual ball bearing CCPM swashplate for 120 or 140 setup
• 24º Collective pitch range

• Main gear ratio 9:1:4.66 with 10 tooth pinion and 90 tooth main gear
• Constant tail drive unit (SE model only)
• Large diameter slipper clutch that drives the tail during autorotations
• Engine mount shims included for multiple engine mounting types
• Clutch bell and lower main shaft bearing block are coupled as one unit for maximum rigidity
• Adjustable clutch bell gear mesh
• Large machined clutch bell support by a 15x24 ball bearing
• Hardened 10 tooth main drive gear
• Heavy duty clutch provides flywheel effect for smooth idle
• Torrington bearing start system eliminates start shaft vibration
• Hardened hex start coupler with 120 set screws
• Efficient cooling fan with location holes for governor magnets
• Split collets to insure alignment for both OS and YS engines are included
• Split collar mast stopper for simple secure main shaft atdjustment
• Machined heavy-duty 14mm delrin gear for heavy loads
• High quality ball bearings with high quality hardware

• High gloss high quality white gelcoated epoxy fiberglass canopy
• Embedded carbon strip reinforcement
• Pre-drilled mounting holes with rubber grommets
• Tinted high gloss windshield
• Pre-cut swashplate, main shaft and starting shaft holes
• Streamlined aerodynamic design for fast forward flight
• High visibility in stable hovering

• Rigid stacked modular aluminum mainframe design with continuous machined lower bearing block assembly
• Fuel tank located on carburator’s centerline for consistant engine operation right side up or inverted
• Large 22 oz fuel tank for long engine run time
• Separate front and rear frames permit engine removal with muffler and carburetor attached
• Rear crossbrace and bottom frame plate provides absolute rigidity in all 3 axis
• Rear engine head design to reduce overall weight and mechanics volume to increase aerobatic maneuverability
• Lightweight machined aluminum engine mount
• Extra long battery tray accomodates radio components including governor and gyro amplifier
• Convenient and easy access to glow plug
• Tough, low-profile and flexible landing gear
• 10mm main shaft thrust bearing (SE model only)

• Tail drive gear off main gear is supported front and back by radial bearings
• Integrated front tail transmission and tail boom eliminates any potential gear mesh and aligment problems
• Bearing supported carbon drive shaft with universal end couplers
• Fully supported carbon tail pushrod with machined aluminum end fittings
• Large hardened heavy-duty metal tail gears
• Two radial and one thrust bearing in each tail rotor blade grip
• Rear rudder servo mount for direct and smooth tail control
• Bearing supported tail pitch lever designed for optimal linear tail pitch
• Flexible 3D style horizontal and vertical tail fins
• Extra large 5x13mm tail output shaft bearing
• Strong lightweight aluminum tail boom
• Dual aluminum tail boom support struts
• Flexable and lightweight 4.5gr 95mm tail blades
• Hardened steel tail output shaft
• Dual carbon support struts and support bridge included (SE model only)
• Carbon horizontal and vertical fin set (SE model only)
• RotorTech 95mm carbon fiber tail blades (SE model only)